Springfield M1D Garand Sniper CMP .30-06 Semi Auto Rifle Scope Case C&R

SOLD FOR: $4977

LSB#: 210419MB02

Make: Springfield

Model: M1D Garand

Serial Number: 2819492

Year of Manufacture: May, 1944  (page 185 of Joe Poyer’s M1 GARAND 1936 to 1957, 6th Edition) Barrel Date: August, 1952

Caliber: .30-06 Springfield

Action Type: Semi Auto, En Block Clip Fed

Markings: There is no import mark.
Receiver: “U.S. RIFLE / CAL. .30 M1 / SPRINGFIELD ARMORY / 2819492”
Trigger Group: “D28290-14-SA – A Springfield part (page 89 of Joe Poyer’s M1 GARAND 1936 to 1957, 6th Edition).
Trigger Guard: “C-46025-W.R.A.” – A Winchester part (page 92).
Hammer: “C46008-3 SA”– A Springfield part (page 97).
Safety: “SA-11” – A Springfield part (page 104).
Follower: Unmarked with a round top – The marking appears to have been lost to refinishing (page 83).
Receiver Leg: “A 1 3 B”, “diamond”, “6” and “D28291-32” – Correct for the Springfield serial number (page 29). It is also marked “TE / 1-69” in electric pencil. This is a January, 1969 Arsenal Rebuild mark from the Toole Armory in Utah.
Op Rod: “D35382 9 SA” – A Springfield part (page 71).
Bolt: “D28287-1W.R.A.”- A Springfield part (page 52).
Barrel Top: “-D7312555”, “A174A -” and with a partial Ordnance Department “crossed cannons” stamping. – Correct drawing number “D7312555” and location for a Springfield M1D barrel of this date (The M1 Garand: World War II by Scott A. Duff www.scott-duff.com/M1D.htm).
Barrel Right Side: “S”, “T”, “P” (twice) and “S-A-8-52” – Correct date range for a Springfield M1D barrel marked in this manner (scott-duff.com/the-m1d-sniper-rifle/).|
The stock, sights and scope assembly are described below.

Barrel Length: Approximately 24 Inches

Sights / Optics: The front sight is a blade set between two protective wings. The rear sight is a fully adjustable aperture set between protective wings. The windage knob is marked “LEFT arrow” twice and “NHC”. The elevation knob is marked from “2-12” in increments of 2 and “NIC”.
The scope is attaches to the rifle with a two piece hinged mount. The mount has an included screw with an oversized head that mates with the base installed on the barrel. The scope is an M84 2.2 power that uses a thin post reticle. The scope appears to have been refurbished or repaired in the past as it no longer has a tapered post reticle (this is common). The scope has a sliding sunshade on the front of the tube and a rubber eyepiece on the rear. It has two adjustment knobs under metal flip caps that turn. The top knob is marked “0 1 2 3 4 5 6 7 8 9”. The side knob is marked “20 15 10 5 R 0 L 5 10 15 20”. There are paint markings on knobs & bases. The scope is marked “TELESCOPE / M84 / SERIAL NO. 11081” on the side plate. The tube & sun shade show scrapes, small scratches and spots of oxidation. The rubber eye piece shows scuffs & small scrapes. The view is mostly clear but does show small light grey flecks. The interior of the mount shows dye and/or paint residue. Overall the scope assembly is in about Very Good condition.

Stock Configuration & Condition: The face of the grip is marked with a “P” proof. The bottom rear of the butt is marked “4” in paint.
The three piece oil finished stock has a pistol grip, metal nose caps, two sling loops, stacking loop and a metal buttplate with a hinged door for storage. The buttplate shows several small scrapes & scratches as well as discoloration on the edge. The bottom of the butt shows 2 empty screw holes that were previously used to secure a cheek piece. The wood shows scrapes, scratches and compression marks. Most of the marks are under the left side of the receiver. The LOP measures 13 1/8 inches from the front of the trigger to the back of the buttplate. The stock rates in about Very Good Plus overall condition.

Type of Finish: Parkerized

Finish Originality: Original to Arsenal Rebuild

Bore Condition: The bore is bright and the rifling is deep. There is no erosion. The bore shows an M.E. of 1. The throat shows a T.E. of 3.

Overall Condition: This rifle retains about 97% of its metal finish. The metal shows several scuffs & light scrapes. The gas tube shows scrapes & small scratches. The right side of the receiver and front of the bolt show light thinning from cycling. The top of the bolt has surface erosion showing through the new finish. The markings are deep. Overall, this rifle rates in about Very Good Plus to Fine condition.

Mechanics: The action functions correctly. We have not fired this rifle. As with all previously owned firearms, a thorough cleaning may be necessary to meet your maintenance standards.

Box, Paperwork & Accessories: The rifle comes with an M84 scope assembly; see above.
The rifle comes with a Civilian Marksmanship Program (CMP) Certificate of Authenticity, CMP Armorer’s Tag, leather cheek piece, M2 Flash Hider and a CMP hard case.
The CMP Certificate lists the purchaser’s name, the rifle’s serial number, the “Mar 30, 2018” purchased date and “Model: M1D Garand Service Grade”. The certificate was stored on top of the rifle in the CMP case. It shows several creases and is in about Very Good Plus condition. The Armorer’s Tag is marked with the rifles serial number and the scopes serial number (red ink). It shows soiling and compression marks. It is in a about Very Good condition.
The leather cheek piece uses leather lacing but is not attached to the rifle. It is stamped “MRT / 2-52” and marked “C311” in ink. It shows discoloration, creasing, light scrapes and compression marks. It is in about Very Good condition.
The Flash Hider is marked “H in a diamond” and “HIDER FLASH M2 / THE HART MFG. CO.”. It shows scuffs, small scrapes and small scratches. It is in about Very Good condition.
The green hard plastic CMP case is marked on both sides “CMP / www.theCMP.org” and with the CMP seal “stars / eagle holding arrows”. The interior of each case has foam pieces that show small compression marks, light soiling and a few small cuts in the foam. The case has 4 latches and 4 reinforced locking holes. The cases show scrapes, scratches and areas of soiling. Overall the case is in about Very Good Plus condition.

Our Assessment: This Springfield M1D Garand Sniper Rifle was purchased through the Civilian Marksmanship Program (CMP) in 2018 and comes with a CMP Certificate of Authenticity. It is in nice shape and has a strong bright bore. It comes with an M84 scope assembly, M2 (cone) flash hider and a Civilian Marksmanship Program (CMP) hard case. The Springfield Armory M1D barrel is marked properly with the correct date and stampings on the top of the barrel. M1D Garands are highly collectable rifles.
Here is some M1D information from Scott Duff (who literally wrote the book on the M1 Garand) over at scott-duff.com/the-m1d-sniper-rifle/:
“As all M1D rifles were rebuilt rifles, the receiver may be of any manufacture and of any serial number produced prior to the date of the rebuild. The same applies to the individual components, any part made prior to the date of the rebuild is correct. All M1D barrels were made by Springfield Armory. The earliest observed M1D barrel is dated 5-51. M1D barrels have been counterfeited and merit careful examination. Nearly all M1D barrels were stamped with drawing number D7312555. M1D barrels manufactured through the fall of 1952 had the drawing number stamped on the top, underneath the rear hand guard. M1D barrels manufactured after the fall of 1952 had the drawing number stamped on the right side, adjacent to the date. The total number of service grade rifles converted by the military to M1D configuration is unknown. However, it is certain that well over 10,000 were converted. No less than 5,000 M1Ds were sold or given to foreign nations. In 1993 and 1994 over 6,000 M1D rifles were deemed obsolete and destroyed under orders from the Secretary of the Army. Beginning in 1995, M1D rifles were sold by the Director of Civilian Marksmanship (DCM), the forerunner to the Civilian Marksmanship Program (CMP) to qualified individuals.”

Springfield M1D Garand Sniper CMP .30-06 Semi Auto Rifle Scope Case C&R
Springfield M1D Garand Sniper CMP .30-06 Semi Auto Rifle Scope Case C&R