Inland Division M1 Carbine .30 Semi Automatic Rifle MFD 1944 C&R

SOLD FOR: $1825

LSB#: 211002NI90

Make: Inland Division of General Motors.

Model: M1 Carbine

Serial Number: 5088593

Year of Manufacture: July to September, 1944 (page 28 of Scott Duff’s book The M1 Carbine Owner’s Guide). Barrel Date: March, 1944

Caliber: .30 Carbine

Action Type: Semi Auto, Detachable Magazine

Markings: There is no import mark. The top of the receiver is marked “U.S. CARBINE / CAL. 30 M1” on the front and “INLAND DIV. / 5088593” on the rear. The top of the barrel is marked “INLAND MFD. DIV. / GENERAL MOTORS / 3 – 44” and “P”. The right rear of the trigger group is marked “INLAND” which is an Inland mark (page 78 of Craig Riesch’s book, U.S. M1 Carbines Wartime Production 7th Edition). The hammer is marked “NI” which is an Inland mark (page 89). The Type IV magazine release is marked “M” which is a USGI replacement part (pages 100-101). The rotary safety is marked “S in a circle” which is a post WWII rebuild mark (page 95 & 185). The inside of the operating slide is marked “W” which is a Winchester mark (page 65). The bolt is marked “1” and “OI” on the left lug which is an Inland mark (page 36). The front sight is marked “RIA” which is a post WWII rebuild mark (page 56 & 185). The Type II rear sight is marked “PI” which was used by Inland and Saginaw Gear (page 29). The Type III barrel band is marked “C” which is a Winchester mark (page 59). The interior of the handguard is marked “W” which is a Winchester mark (page 138). The sling well is marked “OI” which is and Inland mark (page 108-109). The bottom of the grip is marked with a “circled P” proof”. The right side of the butt is marked with a “crossed cannons” cartouche.

Barrel Length: Approximately 18 Inches

Sights / Optics: The front sight is a post set between two protective wings. The rear sight is a Type II adjustable aperture assembly.

Stock Configuration & Condition: The stock has a pistol grip, Type III barrel band with sling loop & bayonet lug, sling well, sling pass through, and a metal buttplate. The buttplate shows scratches, thinning, and discoloration. The barrel band shows scuffs, light scrapes, and light discoloration. The top of the oiler cut out in the butt has been slightly enlarged. The bottom rear of the butt shows deep marks. The wood shows other scrapes & scratches. The LOP measures 13 ? inches from the front of the trigger to the back of the buttplate. The stock rates in about Very Good Plus overall condition.

Type of Finish: Parkerized

Finish Originality: Original

Bore Condition: The bore is bright and the rifling is sharp. There is some fouling in the grooves near the muzzle that should clean up some. There is no erosion. The bore shows an M.E. of 0.0.

Overall Condition: This rifle retains about 97% of its metal finish. The metal shows scuffs and light scrapes. The most prominent marks are on the barrel.  Most of the markings are deep. The barrel markings are well defined. Overall, this rifle rates in about Very Good Plus to Fine condition.

Mechanics: The action functions correctly. We did not fire this rifle. As with all used firearms, a thorough cleaning may be necessary to meet your maintenance requirements.

Box, Paperwork & Accessories: None

Our Assessment: The M1 Carbine was developed and produced after WWII started. Over 6 million were made by a number of U.S. companies to assist with the all out war effort. The M1 Carbine was widely issued to U.S. Military Forces which numbered over 16 million during WWII. The M1 Carbine contributed greatly to U.S. efforts during WWII.
The Inland Manufacturing Division of General Motors was organized in 1922 for the manufacturing of steering wheels. During WWII Inland Division was one of many facilities that tooled up to manufacture M1 Carbines for the war effort. Inland produced the majority of WWII M1 Carbines, about 43%, and contributed greatly to the war effort. Inland M1 Carbines were used by millions of soldiers during WWII in numerous battles. If you see WWII footage that includes an M1 Carbine, it is most likely an Inland M1 Carbine.
This Inland M1 Carbine was made back in 1944. It is in great shape for a wartime military rifle that is over 75 years old. It has been rebuilt and now uses a mix of Inland and USGI parts. The metal & wood are in nice shape and the bore is strong & bright. This Inland M1 carbine will add to your collection and should do well out at the range.